Reduce your nutrient pH sollution with CELLMAX pH- Grow. Developped for the growth phase.

• 38% HNO₃ / Nitric Acid

Reduce your nutrient pH sollution with CELLMAX pH- Bloom. Developped for the bloom phase.

• 59% H₃PO₄ / Phosphoric Acid

Raise your nutrient pH sollution with CELLMAX pH+. 

• 12% KOH / Potassium Hydroxide
• 28.2% K₂O / Potassium Oxide

CANNA pH- Grow can be used to reduce the pH* value of the nutrient solution during the vegetative period.

• 17% HCl / Hydrochloric Acid

CANNA pH- Grow can be used to reduce the pH* value of the nutrient solution during the flowering period.

• 59% H₃PO₄ / Phosphoric Acid

In order to adjust the pH* upwards there is CANNA pH+. This product is suitable for both the growth and the flowering phase.

• 20% KOH / Potassium Hydroxide

Take quick measurements of the EC and temperature of your solution with the Bluelab Conductivity pen!

• completely waterproof
• simple one-point calibration
• 1 year warranty
• Auto-off function to extend battery life
• 1 x AAA alkaline battery (included)
• EC measurement range: 0.0 - 10.0
• accuracy: ± 0.1 at 25°C

Take quick measurements of the pH and temperature of your solution with the Bluelab pH pen !

• completely waterproof
• simple two-point calibration
• 1 year warranty
• Auto-off function to extend battery life
• 1 x AAA alkaline battery (included)
• pH measurement range: 0.0 - 14.0
• accuracy: ± 0.1 at 25°C

The Bluelab Nutrient Meter is designed for hydroponic crops that require a higher than normal level of EC or CF (electrical conductivity or nutrient solution concentration) during their growing cycle.

• completely waterproof
• The length of 40.7cm allows for convenient mixing of the nutrient solution directly in the tank!
• Does not require calibration (factory calibrated)!
• Provides measurements in EC , CF, ppm700 and ppm500 scales
• Auto on/off function
• 5 years warranty
• EC measurement range: 0.2 - 3.6
• EC measurement accuracy: ± 0.1 at 25°C

Bluelab Guardian Monitor allows you simply and effectively to measure pH, conductivity and temperature of the nutrition solution in your reservoir.

• Replaceable Bluelab pH probe included
• Bluelab pH probe cable length: 2m
• No calibration required for the conductivity/temperature probe (factory calibrated)
• Waterproof design
• 2 year warantee for the device
• 6 month warantee for Bluelab pH probe

Measurement range:

• pH: 0.0 - 14.0
• EC: 0.0 - 5.0
• CF: 0 - 50
• ppm 500 (EC x 500): 0 - 2500TDS
• ppm 700 (EC x 700): 0 - 3500ppm
• temperature: 0 - 50°C / 32 - 122°F

Accuracy (at 25°C / 77°F):

• pH: ± 0.1
• EC: ± 0.1
• CF: ± 0.1
• ppm 500 (EC x 500): ± 50TDS
• ppm 700 (EC x 700): ± 70ppm 
• temperature: ±1°C / ± 2°F

ROOT!T Thermostat for Heat Mat is an electronic device that allows complete control over the temperature in the root zone during propagation. By switching the heat mats on and off, it maintains the precisely set desired temperature (10-30ºC). It is compatible with all ROOT!T Heat Mats.

• Maintain optimum temperatures for your plants!
• Easy plug-in operation!
• Easy to use and control!
• Sensor cable length: 1.8m.
• max. load: 1000W / 4.3A

ROOT!T Large Heat Mat evenly warms the root zone, improving germination and rooting. Maintaining a constant temperature is a key factor to success in the early stages, when young plants are most fragile and vulnerable.

• Dimensions W/L: 40x120cm
• Accelerates seed germination or rooting of cuttings with several days.
• Heats the root zone by 5.5-11˚C above ambient temperature.
• Completely waterproof, scratch resistant, durable.
• To set the desired temperature exactly, use with ROOT!T Thermostat for Heat Mat.

ROOT!T Medium Heat Mat evenly warms the root zone, improving germination and rooting. Maintaining a constant temperature is a key factor to success in the early stages, when young plants are most fragile and vulnerable.

• Dimensions W/L: 40x60cm
• Accelerates seed germination or rooting of cuttings with several days.
• Heats the root zone by 5.5-11˚C above ambient temperature.
• Completely waterproof, scratch resistant, durable.
• To set the desired temperature exactly, use with ROOT!T Thermostat for Heat Mat.

ROOT!T Small Heat Mat evenly warms the root zone, improving germination and rooting. Maintaining a constant temperature is a key factor to success in the early stages, when young plants are most fragile and vulnerable.

• Dimensions W/L: 25x35cm
• Accelerates seed germination or rooting of cuttings with several days.
• Heats the root zone by 5.5-11˚C above ambient temperature.
• Completely waterproof, scratch resistant, durable.
• To set the desired temperature exactly, use with ROOT!T Thermostat for Heat Mat.

Glass House Propagator 64 is a propagator made of high-quality hard plastic, suitable for germination, small plants or cuttings.

• size: 59x39x24cm.
• solid, durable and waterproof polypropylene tray
• transparent, impact-resistant polystyrene cover for maximum light permeability
• sliding vents for easy humidity control

Mammoth Pro 120 x 120 x 200cm / 600W is a complete kit for growing plants indoors. The kit includes:

• grow tent Mammoth Pro 120 1pc 
• bulb LUMii BLACK 600W HPS 1pc
• magnetic ballast Hortilight 600W 1pc
• open hammered reflector Stucco 1pc
• analog timer LUMii 1pc
• extraction fan CAN 350m3/h 1pc
• active carbon filter Can-Lite 425m3/h 1pc
• air duct Combiconnect ⌀ 127mm 3m
• duct clamp ⌀ 60 - 135mm 3pcs
• circulating clip fan Garden Highpro 15cm 1pc
• thermo-hygrometer Garden Highpro 1pc
• hangers Rope Ratchet 1pc
• round pot 9.5L 9pcs

Note:

1. The photo is illustrative!
2. The kit is exemplary and can be customized according to the client`s needs.

Mammoth Pro 90 x 90 x 180cm / 400W is a complete kit for growing plants indoors. The kit includes:

• grow tent Mammoth Pro 90 1pc 
• bulb Sylvania GroLux SHP-TS 400W 1pc
• magnetic ballast Electrostart 400W 1pc
• open hammered reflector Stucco 1pc
• analog timer LUMii 1pc
• extraction fan with two speeds Garden Highpro 220-280m3/h 1pc
• active carbon filter Can-Lite 300m3/h 1pc
• air duct Combiconnect ⌀ 127mm 3m
• duct clamp ⌀ 60-135mm 3pcs
• circulating clip fan Garden Highpro 15cm 1pc
• thermo-hygrometer Garden Highpro 1pc
• hangers Rope Ratchet 1pc
• round pot 5L 9pcs

Note:

1. The photo is illustrative!
2. The kit is exemplary and can be customized according to the client`s needs.

Mammoth Pro 300 x 300 x 200cm / 6 x 600W is a complete kit for growing plants indoors. The kit includes:

• grow tent Mammoth Pro 300 1pc
• bulb LUMii BLACK 600W HPS 6pcs 
• magnetic ballast Hortilight 600W 6pcs 
• open hammered reflector Stucco 6pcs  
• G-Systems Timer Box 6x600W 1pc
• outtake box fan Torin 2000m3/h 1pc
• intake box fan Torin 1500m3/h 1pc
• active carbon filter CAN LITE 2000m3/h 1pc
• GSE Temp, Min Speed and Neg Pressure Controller 1pc
• air duct Combiconnect ⌀ 203mm 3m
• metal flange 200mm for box fan 4pcs 
• duct clamp  ⌀ 60 - 270mm 5pcs 
• circulating clip fan Cornwall 20cm 2pcs
• circulating fan Cornwall Multifan 35W 2pcs
• two-point thermo-hygrometer HTC-2 1pc
• hangers Rope Ratchet 4pcs
• round pot 15L 36pcs

Note:

1. The photo is illustrative!
2. The kit is exemplary and can be customized according to the client`s needs.

Cultibox Scrog Net for plants` support. Mesh size: 120, 100 or 80cm.  

• Dimensions: 300x150x200cm.
• Suitable Lighting: 2 x HPS 1000W
• Advisable Ventilation: min. 780m³/h - max. 1000m³/h

• Dimensions: 240x120x200cm.
• Suitable Lighting: 2 x HPS 600W
• Advisable Ventilation: min. 425m³/h - max. 600m³/h

• Dimensions: 300x300x200cm.
• Suitable Lighting: 4 x HPS 1000W
• Advisable Ventilation: min. 1100m³/h - max. 1250m³/h

• Dimensions: 240x240x200cm.
• Suitable Lighting: 4 x HPS 600W
• Advisable Ventilation: min. 780m³/h - max. 1000m³/h

• Dimensions: 120x120x200cm.
• Suitable Lighting: 1 x HPS 1000W
• Advisable Ventilation: min. 250m³/h - max. 380m³/h

Secret Jardin DR150 is a growbox from the elite Dark Room series which is designed for plants with height up to 180cm. The tent comes with two DF25 flanges for connecting with the intake and outtake fans and all the accessories needed to install a complete ventilation system.

• dimensions W/D/H: 150 x 150 x 217cm
• steel poles: ⌀ 25mm
• full 360º plant access
• zippers: 100% lightproof

If you intend to use the spray for watering your plants, you must provide holes where they will out the the excess of food solutions, these holes can make at the bottom of your pots, plates or cubes. Danish trays are curved deeply drains troughs that help the draining ofnutritional solutions away from your plants so the plant will not be permanently in water.There are three sizes of Danish trays, each also includes drainage channels. Werecommend using the thread with a diameter of 25 mm tubes with the same fitting, to be able to direct the waste tank. When you use threaded fittings 25mm, use PTFE tape ensure good connection. Danishtrays should be placed on a stable shelf or stand to be used properly.

If you intend to use the spray for watering your plants, you must provide holes where they will out the the excess of food solutions, these holes can make at the bottom of your pots, plates or cubes. Danish trays are curved deeply drains troughs that help the draining ofnutritional solutions away from your plants so the plant will not be permanently in water.There are three sizes of Danish trays, each also includes drainage channels. Werecommend using the thread with a diameter of 25 mm tubes with the same fitting, to be able to direct the waste tank. When you use threaded fittings 25mm, use PTFE tape ensure good connection. Danishtrays should be placed on a stable shelf or stand to be used properly.

If you intend to use the spray for watering your plants, you must provide holes where they will out the the excess of food solutions, these holes can make at the bottom of your pots, plates or cubes. Danish trays are curved deeply drains troughs that help the draining ofnutritional solutions away from your plants so the plant will not be permanently in water.There are three sizes of Danish trays, each also includes drainage channels. Werecommend using the thread with a diameter of 25 mm tubes with the same fitting, to be able to direct the waste tank. When you use threaded fittings 25mm, use PTFE tape ensure good connection. Danishtrays should be placed on a stable shelf or stand to be used properly.

Air-Pot® 3L is ideal for clones and young plants. Air - Pot® are "breathable" containers that ensure plants will develop strong fibrous roots without circling. And every gardener, from the hobbyist to the professional, knows that healthy roots mean faster growth and better nutrient and water absorption. 

• 60% faster growth and up to 75% more CO₂ absorbed
• diameter: ⌀ 195mm
• height: 220mm
• material: recycled polyethylene

The AutoPot 400 Litre FlexiTank revolutionises water storage, it is everything you need in one compact box. It requires no tools for assembly, reduces storage and shipping costs and takes minutes to assemble. It really couldn’t be simpler. Unlike other waterbutts and barrels, the AutoPot FlexiTank can be stored away when not used, can fit where other tanks cannot go and is adaptable in ways standard tanks are not.

The AutoPot 225 Litre FlexiTank revolutionises water storage, it is everything you need in one compact box. It requires no tools for assembly, reduces storage and shipping costs and takes minutes to assemble. It really couldn’t be simpler. Unlike other waterbutts and barrels, the AutoPot FlexiTank can be stored away when not used, can fit where other tanks cannot go and is adaptable in ways standard tanks are not.

The AutoPot 100 Litre FlexiTank revolutionises water storage, it is everything you need in one compact box. It requires no tools for assembly, reduces storage and shipping costs and takes minutes to assemble. It really couldn’t be simpler. Unlike other waterbutts and barrels, the AutoPot FlexiTank can be stored away when not used, can fit where other tanks cannot go and is adaptable in ways standard tanks are not.

​

The AQUAbox Straight is designed to water and feed plants of all types and sizes that are grown directly in the soil. Positioned directly into the ground the AQUAbox Straight is ideal for watering narrow raised beds. Alternatively, it may be used in a tray to water a conventional grow bag.
AQUAbox Straight is attached to single capillary wick that distributes water under the soil, across an area of up to 4 square feet. With an AQUAvalve at its core, the AQUAbox Straight draws on the water supply (water reservoir) as required by the plants, ensuring an incredibly efficient use of water. The roots of the plants instinctively head towards the water source, attaching themselves to the capillary wicks below the soil level.

A key component in the easy2GO kit. The AQUAvalve cover, when used in conjunction with the AQUAvalve allows the grower to create their own basic, but very effective, hobby system. 

The AQUAvalve is supplied with all AutoPot Watering Systems. Once connected to the water supply the AQUAvalve will control the flow of water to the plants, by simple gravity pressure from a tank or water butt, no pumps, mains water pressure, electricity or timers are required. Once connected to a tank the AQUAvalve will open and allow water to fill the tray to a preset level of 20mm. The AQUAvalve will not refill the tray until all the water has been used.
The AQUAvalve is at the heart of all our watering systems and ensures our systems offer low maintenance, are easily extendable, there is no more hand watering and can water and feed crops whether ornamental or edible all year round. Due to the capacity of the AQUAvalve AutoPot are now market leaders in irrigation whether for domestic gardening, commercial horticulture or hydroponics. The AQUAvalve is a simple but very effective watering device promoting phenomenal growth and maximum yields.

The AutoPot easy2grow Extention kit 8.5 Liter includes:

• 2x 8.5L pots
• 2x Marix discs – the Marix discs are placed inside each of the pots to prevent soil/compost from leaving the pots
• 2x PotSocks – the RCD’s are placed in the tray under each pot, gold face up. The RCD’s will prevent roots from leaving the pots and discourage them from heading towards the AQUAvalve.
• 1x single AQUAvalve with the 2Pot Extension Kit is placed in between the pots.
• 1x 1m of pipe
• 1x 6mm Tee for easy connection to the easy2grow Kit or existing systems.

The AutoPot 1Pot XL System is extremely versatile and can be used for a wide range of plant types and sizes. Seasonal flowering plants and perennial shrubs thrive and produce an abundance of blooms and foliage because of the unique action of the AQUAvalve, which is designed to allow the plant to go through a wet & dry cycle.

All AutoPot products require:

• NO POWER
• NO PUMPS
• NO MAINS WATER PRESSURE
• NO TIMERS

Gravity pressure is all that is needed  from a tank or water barrel. The systems are undoubtedly some of the simplest to use and can be left unattended for weeks due to the capability of the AQUAvalve to deliver all that is required by the plant. 

The AutoPot 1Pot modulе is extremely versatile and can be used for a wide range of plant types and sizes. The AutoPot 1Pot modulе is easily extended so many pots can be linked to a single tank.

All AutoPot products require:

• NO POWER
• NO PUMPS
• NO MAINS WATER PRESSURE
• NO TIMERS

Gravity pressure is all that is needed  from a tank or water barrel. The systems are undoubtedly some of the simplest to use and can be left unattended for weeks due to the capability of the AQUAvalve to deliver all that is required by the plant. The AutoPot 1Pot modulеs can be connected to build even larger systems. See the advice tab for more information or download the 1pot System guide*.

Square pot made of UV-protected plastic with holes on the bottom.

• Capacity: 11L
• Size: 251x251x257mm
• Weight: 0.320kg
• Material: polypropylene
• Made in Italy.

Saucer made of UV-protected plastic for square pot.

• Size: 229x229x30mm
• Weight: 0.078kg
• Material: polypropylene
• Made in Italy.

Square pot made of UV-protected plastic with holes on the bottom.

• Capacity: 9L
• Size: 226x226x238mm
• Weight: 0.250kg
• Material: polypropylene
• Made in Italy.

Saucer made of UV-protected plastic for square pot.

• Size: 210x210x30mm
• Weight: 0.070kg
• Material: polypropylene
• Made in Italy.

Square pot made of UV-protected plastic with holes on the bottom.

• Capacity: 6L
• Size: 210x210x220mm
• Weight: 0.200kg
• Material: polypropylene
• Made in Italy.

Saucer made of UV-protected plastic for square pot.

• Size: 190x190x30mm
• Weight: 0.053kg
• Material: polypropylene
• Made in Italy.

Square pot made of UV-protected plastic with holes on the bottom.

• Capacity: 5L
• Size: 185x185x194mm
• Weight: 0.160kg
• Material: polypropylene
• Made in Italy.

Saucer made of UV-protected plastic for square pot.

• Size: 144x144x26mm
• Weight: 0.034kg
• Material: polypropylene
• Made in Italy.

Square pot made of UV-protected plastic with holes on the bottom.

• Capacity: 2L
• Size: 140x140x150mm
• Weight: 0.100kg
• Material: polypropylene
• Made in Italy.

Designed to meet the needs of large manufacturers, a giant version of the Trimpro Automatik is now available. The Trimpro XL has a larger capacity and a performance ratio 5 times better than its predecessor. The blade height is adjustable to enable precise cutting distance and a single motor regulator adjusts the swirl speed.

• Low noise, efficient, high quality
• Box Dimensions: 88 x 88 x 79 cm
• Assembled: 99.1 x 91.4 x 129.5 cm

Let the TRIMPRO AUTOMATIK do the job for you. Equipped with a powerful three phase motor mated with a variable speed dimmer, height adjustable four (4) blades assembly and a circular hermetic structure that creates a whirlwind effect, the Trimpro Automatik is the fastest and safest way to trim your plants.

We present to you the Tumble Trimmer 45 cm - a revolutionary device that offers fast and accurate trimming of plants. It is designed to optimize your operation while reducing the risk of plant damage.

Leef Kleen Precision Scissors with Straight Tip for more comfortable use.

• 100% inox 
• extra sharp blades
• 100% prime rubber

The ideal tool for clippings! It helps you to make perfect cuts and slopes, this intrument also helps to heal the sick better locations of the plants.

Dual layered Black / White Grow Sheet 85μm 2m / 1m. White to increase light in the grow area, black to reduce external light. The price is for 1 linear meter.

• thickness: 85μm 
• width: 2m
• length: 1m

Waterproofing floor foil. The price is on meter. Width: 4 m

The Diamond Lightite has a raised diamond diffused pattern to spread light more evenly over the canopy of the plant. It also provides maximum reflection of light lumen’s. With PET coated membrane to dramatically increase strength and reduce creasing effect.

• 1.25m Wide 
• 125μm Thick

• Premium Grade Foil
• 5 Layered
• Diamond embossed for light diffusion
• 100% Lightproof

CAN ISO-MAX 250/2310 is a powerful , high-end duct fan. What is unique about this model is that it is a fan built into a silencer . Its metal body is covered with a special noise-insulating material , thus ensuring high performance and low noise levels . The fan is equipped with a Swiss motor , thermal protection against overheating, the ability to adjust the speed and hangers for easier installation.

• metal soundproof housing
• possibility to adjust the revolutions
• capacity: 2310 m ³ /h
• flange: ⌀ 250mm
• power: 273W
• current: 1.7A
• length: 680mm
• weight: 13.4kg

Note: the fan is without a plug!

CAN ISO-MAX 250/1480 is a powerful , high-end duct fan. What is unique about this model is that it is a fan built into a silencer . Its metal body is covered with a special noise-insulating material , thus ensuring high performance and low noise levels . The fan is equipped with a Swiss motor , thermal protection against overheating, the ability to adjust the speed and hangers for easier installation.

• metal soundproof housing
• possibility to adjust the revolutions
• capacity: 1480m ³ /h
• flange: ⌀ 250mm
• power: 150W
• current: 0.9A
• length: 680mm
• weight: 9.9kg

Note: the fan is without a plug!

CAN-FAN RK 150L/760 is an economy class turbine fan with a plastic housing. The fan can be controlled by voltage regulators and is equipped with a thermal switch that turns it off in case of reaching a dangerous operating temperature. The reliable Swiss motor and propeller design provide powerful airflow while making less noise .

• plastic case
• capacity: 760 m ³ /h
• flange: ⌀ 150mm
• power: 105W
• current: 0.5A
• weight: 3.2kg

Note: the fan is without a power cable!

CAN-FAN RK 125L/350 is an economic extraction fan with a plastic housing. The fan can be controlled by voltage regulators and is equipped with a thermal switch that turns it off in case of dangerous operating temperature. The reliable Swiss motor and propeller construction provide powerful airflow while making less noise.

• plastic housing
• capacity: 350m³/h
• flange: ⌀ 125mm
• power: 70W
• current: 0.3A
• weight: 2.3kg

Warning: the fan comes without a power cord!

With this made of galvanazied steel clamp, you can easily fix air ducts with diameters from 60 to 525mm. You only need a scrwedriver to tighten the clamp.

With this made of galvanazied steel clamp, you can easily fix air ducts with diameters from 60 to 270mm. You only need a scrwedriver to tighten the clamp.

With this made of galvanazied steel clamp, you can easily fix air ducts with diameters from 60 to 135mm. You only need a scrwedriver to tighten the clamp.

The Y piece is used for connecting two air ducts to a female coupling.

The Y piece is used for connecting two air ducts to a female coupling.

The Y piece is used for connecting two air ducts to a female coupling.

Reducer ⌀ 250-315mm. The reducer is used for connecting:

• two separate air ducts with different diameters
• two female couplings with different diameters
• female coupling with an air duct with different diameters

Reducer ⌀ 250-300mm. The reducer is used for connecting:

• two separate air ducts with different diameters
• two female couplings with different diameters
• female coupling with an air duct with different diameters

Reducer ⌀ 200-315mm. The reducer is used for connecting:

• two separate air ducts with different diameters
• two female couplings with different diameters
• female coupling with an air duct with different diameters

Reducer ⌀ 200-250mm. The reducer is used for connecting:

• two separate air ducts with different diameters
• two female couplings with different diameters
• female coupling with an air duct with different diameters

Reducer ⌀ 160-250mm. The reducer is used for connecting:

• two separate air ducts with different diameters
• two female couplings with different diameters
• female coupling with an air duct with different diameters

Reducer ⌀ 160-200mm. The reducer is used for connecting:

• two separate air ducts with different diameters
• two female couplings with different diameters
• female coupling with an air duct with different diameters

Reducer ⌀ 125-200mm. The reducer is used for connecting:

• two separate air ducts with different diameters
• two female couplings with different diameters
• female coupling with an air duct with different diameters

Reducer ⌀ 125-160mm. The reducer is used for connecting:

• two separate air ducts with different diameters
• two female couplings with different diameters
• female coupling with an air duct with different diameters

Reducer ⌀ 100-200mm. The reducer is used for connecting:

• two separate air ducts with different diameters
• two female couplings with different diameters
• female coupling with an air duct with different diameters

Reducer ⌀ 100-160mm. The reducer is used for connecting:

• two separate air ducts with different diameters
• two female couplings with different diameters
• female coupling with an air duct with different diameters

Reducer ⌀ 100-125mm. The reducer is used for connecting:

• two separate air ducts with different diameters
• two female couplings with different diameters
• female coupling with an air duct with different diameters

Male Coupling ⌀ 315mm. The coupling is used for connecting two separate air ducts.

Male Coupling ⌀ 300mm. The coupling is used for connecting two separate air ducts.

Male Coupling ⌀ 250mm. The coupling is used for connecting two separate air ducts.

Male Coupling ⌀ 200mm. The coupling is used for connecting two separate air ducts.

Male Coupling ⌀ 160mm. The coupling is used for connecting two separate air ducts.

Male Coupling ⌀ 125mm. The coupling is used for connecting two separate air ducts.

Male Coupling ⌀ 100mm. The coupling is used for connecting two separate air ducts.

Flange ⌀ 315mm. The flange is used for connecting:

• an air duct to a fan box
• to a reducer with a female coupling

Flange ⌀ 250mm. The flange is used for connecting:

• an air duct to a fan box
• to a reducer with a female coupling

Flange ⌀ 200mm. The flange is used for connecting:

• an air duct to a fan box
• to a reducer with a female coupling

Flange ⌀ 160mm. The flange is used for connecting:

• an air duct to a fan box
• to a reducer with a female coupling

Flange ⌀ 127mm. The flange is used for connecting:

• an air duct to a fan box
• to a reducer with a female coupling

Flange ⌀ 100mm. The flange is used for connecting:

• an air duct to a fan box
• to a reducer with a female coupling

Sound-isolated box fan.

• Capacity: 4250m³/h
• Power: 550w
• Amperage: 6A
• Voltage: 230V AC, 50Hz
• Size: 55cm X 55cm X 57cm

Sound-isolated box fan.

• Capacity: 1500m³/h
• Power: 147w
• Amperage: 1.6A
• Voltage: 230V AC, 50Hz
• Size: 40cm X 40cm X 42cm

Sound-isolated box fan.

• Capacity: 1000m³/h
• Power: 230w
• Amperage: 1.1A
• Voltage: 230V AC, 50Hz
• Size: 40cm X 40cm X 42cm

Sonoconnect ⌀ 315mm - 10m is a flexible fully thermal and sound insulating aluminum laminated air duct. Sonoconnect consists of a micro perforated Aluconnect inner hose (covered with a foil to ensure that no glass fibers enter the air flow), 25mm or 50mm insulation and an outer multi-layer polyester laminate cover.

• diameter: ⌀ 315mm
• length: 10m
• fully thermal and sound insulating

Sonoconnect ⌀ 254mm - 10m is a flexible fully thermal and sound insulating aluminum laminated air duct. Sonoconnect consists of a micro perforated Aluconnect inner hose (covered with a foil to ensure that no glass fibers enter the air flow), 25mm or 50mm insulation and an outer multi-layer polyester laminate cover.

• diameter: ⌀ 254mm
• length: 10m
• fully thermal and sound insulating

Sonoconnect ⌀ 203mm - 10m is a flexible fully thermal and sound insulating aluminum laminated air duct. Sonoconnect consists of a micro perforated Aluconnect inner hose (covered with a foil to ensure that no glass fibers enter the air flow), 25mm or 50mm insulation and an outer multi-layer polyester laminate cover.

• diameter: ⌀ 203mm
• length: 10m
• fully thermal and sound insulating